SMTP using wrong IP address on interface with multiple addresses

[d19dotca]

@robi there’s only one interface that I can configure, and multiple IPs are attached to the same interface. So I don’t think it’s so much an interface issue as a selection of which IP to use on the interface.

[d19dotca]

@girish - is there a way to define which IP address is used as the source when sending outbound traffic (i.e. mail)? I'm really struggling with this. My gut tells me this is coming from an OVH DHCP issue, but I've at least gotten the host to send all traffic outbound with a source of my floating IP, however it's now the Cloudron Docker containers that don't seem to be adhering to that, which is where I'm sure OVH Support will point back to Cloudron at that point. So any help on this would be appreciated.

[robi]

@d19dotca In older kernels, additional IPs on say eth0 had additional designations, like eth0:1 or another virtual interface label.

Not sure what it is now..

Does Haraka conf have options for interface/IP priority?

[d19dotca]

Hmm, that rings a bell but I don't think I've seen that for a few years now. The interface (doing a ip a command) shows this:

2: enp5s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether {macAddress} brd ff:ff:ff:ff:ff:ff
    inet {floatingIP} scope global enp5s0f0
       valid_lft forever preferred_lft forever
    inet {autoAssignedIP} metric 100 brd {gatewayIP} scope global dynamic enp5s0f0
       valid_lft 72471sec preferred_lft 72471sec
    inet6 {autoAssignedIPv6} scope link 
       valid_lft forever preferred_lft forever

I assumed too since the floating IP is listed first that it'd be the preferred one, but doesn't seem to be. In the past, I'm pretty sure that's what happened, as long as I added the floating IP higher in the list than the auto-assigned IP, Cloudron's Docker containers would automatically pick up the floating IP.

[Kubernetes]

To change the outgoing traffic to use the floatingIP, you will need to set up a network route or modify the routing table.

Here are the general steps to change the outgoing traffic to use the floatingIP:

Identify the current default gateway IP address by running the command:
ip route show default

Delete the existing default gateway by running the command:
sudo ip route del default (be careful with this as you will lose the connection to your server via ssh and won't be able to set the new default route!)

Add a new default gateway that uses the floatingIP by running the command:
sudo ip route add default via {floatingIP}

Verify the changes by running the command:
ip route show default

After following these steps, the outgoing traffic should now use the floatingIP as the source IP address.

[robi]

The metric param also has a weight function, lower being higher priority.

[girish]

@d19dotca said in SMTP using wrong IP address on interface with multiple addresses:

I recently setup a new dedicated server and noticed that Cloudron is using the default assigned IP address for sending email instead of the static IP address I assigned to both the NIC and the Cloudron configuration under Networking.

The Networking configuration is primarily affecting what IP Cloudron uses to configure the DNS.

It's not routing traffic via this IP etc, all that is handled by the OS/Kernel. In essence, Cloudron relies on Docker and Docker relies on IP tables and routing to route traffic. So, I guess you have to look into IP tables, not sure?

Also, is the Floating IP like DigitalOcean Floating IP? DO floating IP cannot be used as address for outbound traffic , it is only used for incoming traffic. This is because the IP is not assigned to any interface, if I recall correctly.

[d19dotca]

@Kubernetes That sounds like something similar to what ChatGTP told me too so that's good to know. It's strange, because I have what I assumed to be the correct rules in place, as I can run a command curl ifconfig.me and it will now show me the correct IP, but this is for the host, it still uses the unwanted IP if I am running that from a container. So it seems like I need to do something specific to Docker.

@robi said in SMTP using wrong IP address on interface with multiple addresses:

The metric param also has a weight function, lower being higher priority.

Ah yes, I added different weights to mine and still unfortunately see no difference in behaviour. It works fine for host traffic, just not Docker traffic.

@girish said in SMTP using wrong IP address on interface with multiple addresses:

Also, is the Floating IP like DigitalOcean Floating IP? DO floating IP cannot be used as address for outbound traffic , it is only used for incoming traffic. This is because the IP is not assigned to any interface, if I recall correctly.

I don't think that's accurate anymore, as I actually stumbled across this (in part trying to see if I could learn anything from it to apply to OVH, lol): https://docs.digitalocean.com/products/networking/reserved-ips/how-to/outbound-traffic/ - unless "Reserved IP" is different than "Floating IP" for DigitalOcean? Also I found this URL which I was using (it got me in the right direction as my host traffic now goes properly out the floating IP, but just not my Docker traffic yet) which is showing how to use the OVH Floating IP as an outbound source IP: https://medium.com/@PHaroZ_/use-ovh-floating-ip-for-outgoing-traffic-including-from-containers-cd03edaecc3

I'm somehow stuck at trying to get Docker to follow the same rules as my host is following.

[robi]

@d19dotca Agree, you have the outer layer done, now it's up to the inner layer of your Docker networking setup to get it right or follow the host settings/weights.

[girish]

@d19dotca heh, I didn't even know Floating IP got renamed to Reserved IP (in DigitalOcean). Good info!

[d19dotca]

Well I'm kind of ashamed to say it but I gave up, I spent far too many hours on this one (felt like ~25 between the last three days) just on this one single issue in order to avoid an IP block for my clients as Microsoft was blocking the IP of the host machine, and I still couldn't get it to work. I eventually opted instead to create a new Public Cloud instance at OVH instead, migrated all the data to it, using the floating IP, and things seem to be working fine now (only accessible with one public IP address so Docker had no other choice, lol). Sorry there's no confirmed solution to this one.