Email sending broken after updating to 8.2.x (due to IPv6 issues)

[humptydumpty]

@dsp76 I have it as ::/64 which is my full IPv6 address as shown at dash > IP's > IPv6 and it's been working fine for me. In case it matters, I'm on the CCX plan (VDS).

Edit: asked chatgpt about this and it looks like I got it wrong too (possibly a security issue too). But, it mentioned that ::1 might be reserved by Hetzner so we'll need to manually assign it to something else.

That means your IPv6 address is `xxxx:xxx:xx:xxxx::1`, and it’s using the `/64` subnet.  

If others have had issues with `::1`, you might want to pick another address, like `::100` or `::abcd`. You can assign it manually with:  


ip -6 addr add xxxx:xxx:xx:xxxx::100/64 dev eth0
 

Then, set the PTR record for `xxxx:xxx:xx:xxxx::100` in Hetzner’s panel. If everything works, make it persistent by adding it to your network config (`/etc/network/interfaces` or equivalent, depending on your OS). 

Edit 2: so dug some more and setting the ptr to cover the entire /64 block is a bit riskier. With that said, it's OK in my case since I'm using Hetzner's vDedicated (CCX) plan and according to Mr.GPT, I'm the sole user on for that IP. Also, security wise, I'm in the clear if I have set SPF, DMARC, and DKIM records.

I did a Reverse lookup on Mxtoolbox for my IPv6 address and it's reporting back my mailserver domain .

Give it a shot and see if that works for you.

[jdaviescoates]

@humptydumpty I've got a dedicated server with Hetzner and having /64 at the end didn't work for me:

@jdaviescoates said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

I had tried this:

Screenshot from 2025-01-14 12-45-06.png

Which hadn't worked, but looking at https://docs.hetzner.com/cloud/servers/cloud-server-rdns/ gave me the clue that I should remove the /64 bit and now it seems to have worked!

[humptydumpty]

@jdaviescoates Does it fail the reverse lookup or Hetzner doesn't save the entry?

[jdaviescoates]

@humptydumpty said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

Hetzner doesn't save the entry?

This. Hetzner just says it's invalid.

[avatar1024]

@girish said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

If your VPS provider does not allow you to set IPv6 PTR , then just disable IPv6 in the interfaces. sysctl -w net.ipv6.conf.ens18.disable_ipv6=1 for example . You have to put net.ipv6.conf.ens18.disable_ipv6=1 in your /etc/sysctl.conf for this to persist reboots. After you do this, also disable IPv6 in Cloudron, Network -> IPv6 -> Disable.

Hi @girish,

IPv6 keeps coming back on on my servers network interface (it's not activated on Cloudron). Every so often curl https://ipv6.api.cloudron.io/api/v1/helper/public_ip keeps returning the IPv6 address and I get the Gmail errors again. I have done both: sysctl -w net.ipv6.conf.ens18.disable_ipv6=1 and put net.ipv6.conf.ens18.disable_ipv6=1 in /etc/sysctl.conf (replacing ens18 by eth0 which does disable IPv6 for that interface...but then after a while it comes back on).

Any idea?

[joseph]

@avatar1024 I would check if ens18 is actually your interface ? ip addr

[avatar1024]

@joseph said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

@avatar1024 I would check if ens18 is actually your interface ? ip addr

sysctl -w net.ipv6.conf.ens18.disable_ipv6=1 returns
sysctl: cannot stat /proc/sys/net/ipv6/conf/ens18/disable_ipv6: No such file or directory

whereas

sysctl -w net.ipv6.conf.eth0.disable_ipv6=1 returns
net.ipv6.conf.eth0.disable_ipv6 = 1

and subsequently

curl https://ipv6.api.cloudron.io/api/v1/helper/public_ip returns as expected
curl: (7) Failed to connect to ipv6.api.cloudron.io port 443 after 1 ms: Couldn't connect to server, instead of the IPv6 address which shows IPv6 is deactivated.

So I'm pretty sure eth0 is the correct one (also, when active, the IPv6 address is displayed for that interface via ifconfig).

And it all works fine temporarily, it just doesn't stays that way, even after adding net.ipv6.conf.eth0.disable_ipv6=1 at the bottom of the /etc/sysctl.conf file.

[avatar1024]

Right so, after adding to /etc/sysctl.conf:

net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1
net.ipv6.conf.eth0.disable_ipv6 = 1

on reboot, cat /proc/sys/net/ipv6/conf/all/disable_ipv6 return 1 so one would think it's all good, but it isn't. curl https://ipv6.api.cloudron.io/api/v1/helper/public_ip still retunrs the IPv6 address and I can still see it in ifconfig for the network interface. Yet manually running either sysctl -p or sysctl -w net.ipv6.conf.eth0.disable_ipv6=1 post boot works just fine to disable IPv6. So there is something at boot time that prevents disabling IPv6.

I therefore went the bulletproof way and disabled ipv6 as a boot argument in grub (GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1"). But then I got of errors at boot time when services start, especially for nginx so that;s not working either.

Any idea?

[joseph]

@avatar1024 usually, if that happens it's because something else is enabling ipv6 on the interface. Do you use netplan? If so, I could chek /etc/netplan/50-cloud-init.yaml . Does it have some statically assigned ipv6 block?

[avatar1024]

@joseph said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

Do you use netplan? If so, I could chek /etc/netplan/50-cloud-init.yaml . Does it have some statically assigned ipv6 block?

I was not aware I did use netplan (I don;t even really know what it is), but yes there is this config file and it seems to contain static IPs, see:

network:
  version: 2
  ethernets:
    eth0:
      match:
        macaddress: "xx:xx:xx:xx:xx:xx"
      addresses:
      - "152.xx.xx.43/22"
      - "2a03:4000:xx:xx:xxxx:xxxx:xxxx:6007/64"
      nameservers:
        addresses:
        - 46.38.225.230
        - 46.38.252.230
        - 2a03:4000:0:1::e1e6
      routes:
      - to: "default"
        via: "152.xx.xx.1"
      - on-link: true
        to: "default"
        via: "fe80::1"

If you tell me how i should modify the file then I'll try it out.

Thanks a lot for your help.

[joseph]

@avatar1024 said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

  - "2a03:4000:xx:xx:xxxx:xxxx:xxxx:6007/64"

yup, this is the culprit. The IPv6 address is statically assigned here. You have to put a # in front of the line to comment it out and reboot the machine.

[avatar1024]

@joseph said in Email sending broken after updating to 8.2.x (due to IPv6 issues):

yup, this is the culprit. The IPv6 address is statically assigned here. You have to put a # in front of the line to comment it out and reboot the machine.

THANK YOU! That worked.

Seems like netplan is here by default since Ubuntu 18: https://pscl4rke.wordpress.com/2019/10/01/disabling-ipv6-on-ubuntu-18-04-the-netplan-version/

[joseph]

@avatar1024 I found this https://github.com/canonical/netplan/blob/main/doc/netplan-tutorial.md#editing-netplan-yaml-files-to-disable-ipv6 . Can't figure where this page is "published" . The yaml ref is at https://netplan.readthedocs.io/en/latest/netplan-yaml/

[potemkin_ai]

Just for the reference: netplan try is usually a better way, as it might save from end up getting locked out from the server. I also usually run a background cron task, that removes those temporary files from /etc/netplan, when messing with the network.