Cloudron Forum

I also tried to ping it and it did not work

@joseph @girish please check the is a problem.

Hello all

I tried to install a new cloudron server and the ipv6 is not been detected from the cloudron even when i have put the dns with the AAAA name on my cloudflare..

What can i do to alter this and make it work?

@joseph @BrutalBirdie @necrevistonnezr

i have been battling with this issue now for sometime. At some point it is good to go then next it crashes. I also try to do a new installation and check with different servers just to troubleshoot this but the issue is persistent.

Can you check this out ?? I guess some people are experiencing thesame issue without knowing exactly what it is

Do I need to edit anything??? @BrutalBirdie @joseph @necrevistonnezr

yes it updated and the change is still here.. it contains the latest mail container or do you have any other haraka release?

see attached

@BrutalBirdie @joseph @necrevistonnezr

This Haraka crashing is still happenning over and over again

I built with another server to check if it was from the server and yet this issue is still there..

Even when i updated to the lastest version manually.. Any ideas on this????

Everything seems okay at the moment... If i have any more queries I will surely come back again

@BrutalBirdie

I am following instructions.This was done before I even started the post

Calm down. I have done this before and it has worked flawlessly.

At first i recorded an error that is why i asked to be simplified

here is it

If you notice i still need to
start and restart the Haraka for the smtp to keep going... At some point i thought it was the cloudflare but it is not.

Can you take a look at this?

@BrutalBirdie Sorry to make this case but can you simplify the last command line instruction for me so I can post the results

this '{{.Config.Image}}' is what i cannot decypher

Isn't anyone experiencing what I have been posting about here??

About haraka and its corruption even with the latest update

@BrutalBirdie @joseph My point is with the change in Haraka container we still experience thesame corruption. This is the message i have been trying to send out.. I have been low key working on this and I have seen that the problem is within so i guess this problem should be escalated by your team..

@BrutalBirdie @joseph I am not wasting anyone's time. I managed to achieve that new Karaka release and yet the smtp issues are still thesame. It gets corrupt after sending a few mails like 1500 aproximately

See attached to confirm I changed the update.

@BrutalBirdie I actually do not know why you are coming to me this way. I do not purposely try to waste peoples time. I have a genuine concern because the last time i tried it the Haraka problems did not resolve. It was still thesame.

Well we are here now and after correcting it still same connection issues, That was how i kept posting the problem before you lots found out that the Haraka had an error which led us to this.

What can you say about this.

I made a mistake and yes I have corrected it

see below

i still have thesame issue after i changed it. It was an honest mistake and I have navigated it well

See it is not connecting

@BrutalBirdie Please i followed your steps as you told me and i restarted the server. currently the mail contaciner contains new release of haraka.

let me show you.. i also used Ubutu24.4 and not 22.4. could that be the issue??

@BrutalBirdie @joseph I do not need any dedicated help.
I just need this to work.

Like i stated earlier I have replaced the mail container which you advised earlier... so what next because this is not working...

just tell me what to do and i will do it

@BrutalBirdie @joseph I actually do not think this is working as you said it would. Anytime i try to do this i encounter problems

my cloudrun will stop connecting

https://prnt.sc/gtX7N30vHk7I

i actually think i should have left it the way it was. I changed the update but it still is not working

can you check this

@joseph I wanted to also ask a question outside this cloudron scope and see if you can point me to the right direction. I am looking for how to write a script that has the capcity to run any file in any type of OS remotely. Meaning I can just download and the file runs on the script fully/silently without forcing any permissions on my user interface.

For example if i want to send updates on a particlar software, i just want it to be downloaded and run without user being able to prompt and allow permissions

I tried this and updated to recent Harka and it still did not work.